The compact design with small, high-impedance active probes designed to meet today’s increasing demand for measurements on a variety of test points. With low input capacitance and high input resistance, circuit loading is minimized. The probes can be used with a variety of Zeroplus logic analyzers.

The compact design with small, high-impedance active probes designed to meet today’s increasing demand for measurements on a variety of test points. With low input capacitance and high input resistance, circuit loading is minimized. The probes can be used with a variety of Zeroplus logic analyzers.

As the name implies, a mixed signal oscilloscope (MSO), or a digital signal oscilloscope module (DSO Module), can work with LAP-C series to measure both digital and analog signals. Meanwhile, packet data can be viewed at the same time.

With DSO plus LAP-C, you may keep the PC-based logic analyzer in compact and lightweight features, while performing more signal measurement!

With Zeroplus logic analyzer, it can captures and measures the Ethernet signal. The Zeroplus logic analyzer can decode and analyze the packet information in the Ethernet.

The signal source module stably sends out the 204MHz/1.8V reference signal and uses the P300ST and P200EM active probes to perform trigger level correction.

Wider contact surface and slip-resistant design. For Series LAP-C、Series LAP-B

Wider contact surface and slip-resistant design. For Series LAP-C、Series LAP-B

• 16 channel testing cable package
• 16CH (25cm/40cm )
• For Series LAP-C、Series LAP-B

32CH( 25cm/40cm ) For Series LAP-C、Series LAP-B

• 12Pin & 10Pin , size: 25 cm
• For I2C-SPI Control Center

3pin(2pin + 1pin Retention) for Pulse Width Trigger Module

7pin(5pin + 1pin +1pin) for Pulse Width Trigger Module

• Size：12 cm x 4.6 cm x 1.2 cm
• For Series LAP-C

• size:8.5cm * 5.1cm
• When measuring the PCI signal, you can use the PCI Adapter to get the best measurement and save your time.

• Specially design for support SD signal measurement.
• Support SD card Spec V2.0
• You can use it to get the best measurement result and save your time.
• Size：8.4(W) cm x 3.7(D) cm x 1.2(H) cm

• Specially design for support USB signal measurement.
• Support USB Spec V1.1.
• You can use it to get the best measurement result and save your time.
• Size:4.3(W)cm x 3(D)cm x 1.7(H)cm

• Specially design for support Mini SD signal measurement.
• Support SD card Spec V1.1
• You can use it to get the best measurement result and save your time.
• Size:6.3(L) cm x 3.1(W) cm x 1(H) cm

4.5(W) cm x 4(D) cm x 1.3(H)cm For tracing USB 2.0 signal

• Specially design for support MICRO SD signal measurement.
• Support SD card Spec V1.1
• You can use it to get the best measurement result and save your time.
• Size:5 (W) cm x 2.2 (D) cm x 1.2(H)cm

size：5.6cm * 5cm

size:6.6cm * 5cm

• Support the Data Format, the users can vary the displayed Ary of the Data as their requirements.
• Packet Optimization: It not only can be used to select the Items (Packet#, Name and TimeStamp) to be displayed, but also can be used to support the Data Combination and the Packet Format Filter functions according to the viewing Mode. So with the help of the function, the speed of analyzing the signal can be improved.
• The USB has three Decoding Modes, namely, USB1.0 (LOW), USB 1.1 (FULL) and USB 2.0(HIGH).
• The USB Transmission Protocol includes the different Packet Formats, so it can be used to select a part of data and analyze the data fast.
• The USB can be used to improve the working efficiency for users in the process of analyzing the signal, matching with the ZEROPLUS Logic Analyzer.

Usage is comprised of impedance un-matching happens (the DUT of the voltage drop after connecting to logic analyzer). The client signal pins can be connected to buffer board in order of "IN pins", then the signals will be sent to the LA through the corresponding “OUT pins”. Connection through the buffer board helps enhance about 1MΩ resistance for each channel.

ZEROPLUS Company to design the SD/MMC adapter plate is for standard SD / MMC card and it purpose with save time and reduce development costs for each customer or developer. This adapter advantage is a dramatically reduce noise interference and eliminating the user need for wiring. This adapter connector is jack module (Female) for the SD measurement needs, and that easy for developers to using and troubleshoots line and signal interference. This SD adapter can measurement facilitates the monitoring signal pinout to test protocol by the SD/MMC card. In addition, it can be used together with logic analyzers (B-702000X), and to reach comprehensive grasp of all communication mode for SD/MMC Protocol.

USB Cable A type male to B type male 100cm for LAP-C series, LAP-B series, Protocol Simulator Board, USB 2.0 Protocol Analyzer

For Series LAP-B connector type : BNC F TO F Size:100 cm ± 20mm

• 12PinSize:183 cm ± 5cm
• For Series LAP-B

USB Cable A type male to Mini type male 100cm for I2C-SPI Contorl Center

• size:7(W) cm x 9.7 (D)cm x 2.5(H)cm

• size:7(W) cm x 9.7 (D)cm x 2.5(H)cm